Difference between revisions of "Documentation/4.2/Extensions/XNATSlicer"

From Slicer Wiki
Jump to: navigation, search
Line 50: Line 50:
 
File:XNATSlicer-Perms3-4.jpg|3. Go to the "Security" Tab. Click on "Users" (or the equivalent group) under the "Groups or user names:" category.  Then click the "edit button".  A "Permissions" window will pop up.  In the "Permissions" window, select "Users" again and make sure "Allow" is checked for all options. Hit "OK."
 
File:XNATSlicer-Perms3-4.jpg|3. Go to the "Security" Tab. Click on "Users" (or the equivalent group) under the "Groups or user names:" category.  Then click the "edit button".  A "Permissions" window will pop up.  In the "Permissions" window, select "Users" again and make sure "Allow" is checked for all options. Hit "OK."
 
File:XNATSlicer-Perms5.jpg|4. You should now see that Users have Read+Write access for the Slicer install folder.
 
File:XNATSlicer-Perms5.jpg|4. You should now see that Users have Read+Write access for the Slicer install folder.
 +
</gallery>
 
You're all set.  Just load up the XNATSlicer module and click the "Login" button, and the module will install the additional libraries for you.  If you need a walkthrough, look [[#First Login|below]].<br>
 
You're all set.  Just load up the XNATSlicer module and click the "Login" button, and the module will install the additional libraries for you.  If you need a walkthrough, look [[#First Login|below]].<br>
</gallery>
 
 
 
<!-- ---------------------------- -->
 
<!-- ---------------------------- -->
 
{{documentation/{{documentation/version}}/module-section|First Login}}
 
{{documentation/{{documentation/version}}/module-section|First Login}}
 
{|
 
{|
 
|}
 
|}
 
+
<gallery widths=230px heights=230px perrow=4>
1) During your first login, the XNATSlicer module will install it's external libraries for you.  Just click the "Login" button.<br>
+
File:XNATSlicer-LibInstall1.jpg|1. During your first login, the XNATSlicer module will install it's external libraries for you.  Just click the "Login" button.
[[File:XNATSlicer-LibInstall1.jpg]]
+
File:XNATSlicer-LibInstall2.jpg|2. You'll be notified that the module will install external libraries.  Hit "OK."
 
+
File:XNATSlicer-LibInstall3.jpg|3. You'll be warned that you need full [[#Install Instructions|Read+Write]] access to your Slicer install directory.  Assuming you followed the [[#Install Instructions|instructions above]], hit "OK."
 
+
File:XNATSlicer-LibInstall4.jpg|4. A popup will appear telling you what libraries are being installed.
2) You'll be notified that the module will install external libraries.  Hit "OK."<br>
+
File:XNATSlicer-LibInstall5.jpg|5. You'll be asked to reset Slicer.  Afterwards, just log in to your XNAT host of choice and you're all set.  See the [[#Panels and their use|"Panels and their use"]] section.
[[File:XNATSlicer-LibInstall2.jpg]]
+
</gallery>
 
 
 
 
3) You'll be warned that you need full [[#Install Instructions|Read+Write]] access to your Slicer install directory.  Assuming you followed the [[#Install Instructions|instructions above]], hit "OK."<br>
 
[[File:XNATSlicer-LibInstall3.jpg]]
 
 
 
 
 
4) A popup will appear telling you what libraries are being installed.<br>
 
[[File:XNATSlicer-LibInstall4.jpg]]
 
 
 
 
 
5) You'll be asked to reset Slicer.  Afterwards, just log in to your XNAT host of choice and you're all set.  See the [[#Panels and their use|"Panels and their use"]] section.<br>
 
[[File:XNATSlicer-LibInstall5.jpg]]
 
  
  

Revision as of 19:11, 11 February 2013

Home < Documentation < 4.2 < Extensions < XNATSlicer


Introduction and Acknowledgements

XNATSlicer-Med.png
Extension: XNATSlicer
Acknowledgments: TBD
Author: Sunil Kumar (Washington University in St. Louis)
Contributors: Dan Marcus (Washington University in St. Louis), Steve Pieper (SPL)
Contact: Sunil Kumar, <email>kumars@mir.wustl.edu</email>

National Alliance for Medical Image Computing (NA-MIC)  
The Neuroinformatics Research Group - WUSTL  

Module Description

Secure GUI-based IO with any XNAT server. Powered by PyXNAT. Win64 for now.


Features:

  • Download and view
    • Scans (individual or batch)
    • Bundled Slicer scenes (*.mrb)
    • Any Slicer-readable file
  • Upload
    • Bundled Slicer scenes (*.mrb)
  • Other
    • Project and folder creation
    • File deletion

Install Instructions

The only step needed is to make sure you have Read+Write permissions for your Slicer install directory. (If you already do, you can proceed to the First Login section.)

You're all set. Just load up the XNATSlicer module and click the "Login" button, and the module will install the additional libraries for you. If you need a walkthrough, look below.

First Login


Use Cases

Tutorials

Panels and their use

XNATSlicer
  • Secure login
  • Status updater
  • Project and file browser
    • Traverse via tree
    • Download/view
    • Upload
    • Create projects and folders
    • Delete folders and files

Similar Modules

References

Information for Developers