Slicer-3.6-QA

Return to Slicer 3.6 documentation

• This page contains our assessment of the Slicer 3.6 modules

• See also the module culling event at the end of April 2010

Testing Status

Slicer 3.6 Quality Assurance

Score	Name	Documentation	Help	Acknowledgment	Test coverage	valgrind errors
Gold	my module	complete	yes and yes	yes, yes, yes	80%	0
??	Camera	complete	yes, no link	no	0%	unknown
??	Volumes	complete	yes and yes	yes and yes	0%	unknown
??	Diffusion Editor	complete	yes and yes	no	0%	unknown
??	Models	complete	yes and yes	yes and yes	0%	unknown
??	Measurements	complete	yes and yes	no and yes	0%	unknown
??	Fiducials	complete	yes and yes	no	0%	unknown
??	Data	complete	yes and yes	yes and yes	0%	unknown
??	Slices	complete	no	no	0%	unknown
??	DiffusionWeightedTest				0%	unknown
??	Colors	complete	yes and no	yes and no	0%	unknown
??	DiffusionTensorEstimation				0%	unknown
??	DiffusionTensorMathematics				0%	unknown
??	OrientImage				0%	unknown
??	LinearRegistration				0%	unknown
??	RigidRegistration				0%	unknown
??	AffineRegistration				0%	unknown
??	BSplineDeformableRegistration				0%	unknown
??	TestGridTransformRegistration				0%	unknown
??	CheckerBoard				0%	unknown
??	ResampleVolume				0%	unknown
??	PolyDataToLabelmap				0%	unknown
??	GaussianBlurImageFilter				0%	unknown
??	ConfidenceConnected				0%	unknown
??	ExecutionModelTour				0%	unknown
??	ImageReadDicomWrite				0%	unknown
??	CurvatureAnisotropicDiffusion				0%	unknown
??	GradientAnisotropicDiffusion				0%	unknown
??	MedianImageFilter				0%	unknown
??	DWIDicomLoad				0%	unknown
??	HistogramMatching				0%	unknown
??	OtsuThresholdImageFilter				0%	unknown
??	OtsuThresholdSegmentation				0%	unknown
??	Subtract				0%	unknown
??	Multiply				0%	unknown
??	Add				0%	unknown
??	Threshold				0%	unknown
??	Mask				0%	unknown
??	Cast				0%	unknown
??	VotingBinaryHoleFillingImageFilter				0%	unknown
??	ModelMaker				0%	unknown
??	MultipleModelsExample				0%	unknown
??	GrayscaleModelMaker				0%	unknown
??	MergeModels				0%	unknown
??	GrayscaleFillHoleImageFilter				0%	unknown
??	GrayscaleGrindPeakImageFilter				0%	unknown
??	LabelMapSmoothing				0%	unknown
??	ImageLabelCombine				0%	unknown
??	ResampleVolume2				0%	unknown
??	ZeroCrossingBasedEdgeDetectionImageFilter				0%	unknown
??	FreesurferSurfaceSectionExtraction				0%	unknown

Testing Partition

Most Slicer modules have a GUI component and a Data Processing component.

Testing GUI components is still a challenge, so we will focus here on testing the Data Processing components. This can be done in most cases by partitioning the module into a GUI section and a Data Processing section, where the second one usually takes the form of a C++ class (although that is not a requirement).

The data processing section can be tested by using standard CTest/CMake mechanisms. Basically by adding ADD_TEST() entries to the CMakeLists.txt file of the module.

Luis Ibanez' scoring system

The following scoring will be applied to the data processing sections of all modules:

Slicer 3.6 Quality Assurance Scoring

Score	Code Coverage	Valgrind Errors	Documentation	Tutorial
Gold	> 80%	0	yes	yes
Silver	> 70%	< 10	yes	yes
Bronze	> 60%	< 50	yes	yes
Clay	> 50%	< 100	yes	yes
Coal	> 50%	> 100	yes	yes
Hazard	unknown	unknown	no	no

The code coverage and Valgrind error must be the ones reported on the Nightly Slicer Dashboard. Anecdotal data is not acceptable.